Error Codes
Error codes displayed on the HMI.
- 0047 Control Cabinet Safety Switch, Left
- 0065 Safety Guard, Front
- 0067 Safety Guard, Side Rear
- 0070 Safety Flap
- 0071 Funnel Open, Dosing Auger
- 0073 Discharge Conveyor is not in Position
- 0074 Safety Switch Infeed Auger
- 0075 Safety Switch Auger Tube
- 0078 Protective Tunnel ‒ Discharge Conveyor 1
- 0048 Control Cabinet Safety Switch, Right
- 0063 Safety Chain Open Emergency Stop
- 0066 Safety Guard, Side Front
- 0069 Safety Guard, Side Top
- 0072 Infeed Closure
- 0076 Drop Pipe Safety Switch
- 0077 Safety Switch ‒ Control Cabinet
- 0079 Protective Tunnel ‒ Discharge Conveyor 2
- 0080 Protective Door Side Bottom
- 0084 Safety Guard Right
- 0085 Safety Guard Rear
- 0087 Roller Support Safety Door
- 0088 Safety Door, Laser Printer
- 0081 Safety Switch Perforation
- 0083 Safety Guard Left
- 0086 Safety Cover Transverse Jaws
- 0089 Safety Door, Reserve 1
- 0090 Safety Door, Reserve 2
- 0092 Roller Support Safety Door, Right
- 0091 Roller Support Safety Door, Left
- 0093 Roller Support Safety Door, Rear
- 0098 Safety Door Side Top Left
- 0099 Safety Door Side Top Right
- 0094 Roller Support Safety Door, Top
- 0095 Safety Chain Open, Protective Doors
- 0096 Machine Housing Safety Door, Left
- 0097 Machine Housing Safety Door, Right
- 0129 Pressure Monitor
- 0130 Fault - Forced Venting
- 0131 Pressure Monitor 2
- 0256 Rovema Software Key Incorrect
- 0260 Batch Number Reached
- 0263 Infeed Fault
- 0132 Fault - Forced Venting 2
- 0265 Scale Fault
- 0268 Drop Time Setting is Too High
- 0271 Transport Belts Lifted Off
- 0272 Gas Flushing Monitor
- 0274 Pre-fuse Heating
- 0275 Overtemperature – Control Cabinet
- 0276 Attention, Main Switch Heating Off!
- 0277 Gas Flushing Fault
- 0288 Barcode Scanner Error
- 0292 Barcode Scanner Not Ready
- 0264 Checkweigher Fault
- 0269 Unable to Determine External Cycle Number
- 0270 External Synchronous Pulses Not Present
- 0273 Remote Connection Not Active Touch Panel
- 0289 Wrong Barcode
- 0291 Timed Out - Barcode Not Read
- 0400 Sealing Jaw Drive Vertical Module Hardware Fault
- 0401 Sealing Jaw Drive Vertical Drive Overtemp
- 0402 Sealing Jaw Drive Vertical Motor Overtemp
- 0404 Sealing Jaw Drive Vertical Motion Instruction Error
- 0408 Sealing Jaw Drive Vertical Over Voltage Fault
- 0415 Sealing Jaw Drive Vertical Other Fault, Call Service
- 0424 Film Drive Bus Regulator Fault
- 0405 Sealing Jaw Drive Vertical Feedback Fault
- 0407 Sealing Jaw Drive Vertical Over Current Fault
- 0409 Sealing jaw drive vertical under voltage fault
- 0410 Sealing Jaw Drive Vertical Phase Loss
- 0411 Sealing Jaw Drive Vertical Position Error
- 0412 Sealing Jaw Drive Vertical Excessive Velocity Fault
- 0413 Sealing Jaw Drive Vertical Over torque Limit Fault
- 0414 Sealing Jaw Drive Vertical Under torque Limit Fault
- 0416 Film Drive Motor Thermal Overload
- 0417 Film Drive Thermal Overload
- 0419 Film Drive Converter Pre-charge Fault
- 0420 Film Drive Motor Feedback Fault
- 0428 Film Drive Physical Axis Fault
- 0429 Film Drive Ground Short Fault
- 0430 Film Drive CPU Watchdog Fault
- 0431 Film Drive Overspeed Fault
- 0432 Film Drive Module Hardware Fault
- 0433 Film Drive Overtemp
- 0435 Film Drive Duplicate address Faullt
- 0436 Film Drive Motion Instruction Error
- 0437 Film Drive Feedback Fault
- 0434 Film Drive Motor Overtemp
- 0439 Film Drive Over current Fault
- 0587 Temperature Too Low, Rear Jaw
Temperature
- 0369 Sealing Jaw Drive Horizontal Drive Overtemp
- 0465 Gusseting Device Drive Overtemp
- 0449 Gusseting Device Thermal Overload
- 0546 No Change in Temperature on Left Vertical Jaw
- 0547 Temperature Too Low Left Vertical Jaw
- 0552 Temperature Too Low Right Vertical Jaw
- 0553 Overtemperature Right Vertical Jaw
- 0548 Overtemperature Left Vertical Jaw
- 0551 No Change in Temperature on Right Vertical Jaw
- 0581 No Change in Temperature on Rear Jaw
- 0584 No Change in Temperature on Vertical Jaw
- 0585 Temperature Too Low, Front Jaw
- 0588 Temperature Too High, Rear Jaw
- 0589 Temperature Too Low Vertical Jaw
- 0590 Overtemperature Vertical Jaw
- 0586 Temperature Too High, Front Jaw
- 0645 Overtemp Unwinder
- 0647 Overtemp. Vacuum Pump
- 0643 Overtemp. Vertical Sealing Belt Drive
- 0606 Overtemperature Discharge Conveyor
- 0715 Overtemperature Mixer
- 0717 Overtemperature Motor Infeed
- 0786 Overtemp. Volume Adjustment
- 0097 Check Temperature of Control Cabinet
- 0230 Temperature Too Low, Front Jaw
- 0231 Temperature Too High, Front Jaw
- 0233 Temperature Too Low, Rear Jaw
- 0234 Temperature Too High, Rear Jaw
- 0236 Temperature Too Low Vertical Jaw
- 0237 Overtemperature vertical jaw
- 0239 Temperature Too Low Left Vertical Jaw
- 0240 Overtemperature Left Vertical Jaw
- 0242 Temperature Too Low Right Vertical Jaw
- 0243 Overtemperature Right Vertical Jaw
Printer
Jaw Drive
- 0372 Sealing Jaw Drive Horizontal Motion Instruction Error
- 0388 Sealing Jaw Drive Vertical Motor Fback Fault
- 0360 Sealing Jaw Drive Horizontal Bus Regulator Fault
- 0356 Sealing Jaw Drive Horizontal Motor Feedback Fault
- 0387 Sealing Jaw Drive Vertical Converter Pre- charge Fault
- 0355 Sealing Jaw Drive Horizontal Converter Pre-charge Fault
- 0352 Sealing Jaw Drive Horizontal Motor Thermal Overload
- 0353 Sealing Jaw Drive Horizontal Drive Thermal Overload
- 0603 Product Between Jaws
- 0226 Product Between Jaws
- 0375 Sealing Jaw Drive Horizontal Overcurrent Fault
- 0371 Sealing Jaw Drive Horizontal Duplicate Address Flt
- 0403 Sealing Jaw Drive Vertical Duplicate Address Fault
- 0399 Sealing Jaw Drive Vertical Overspeed Fault
- 0399 Cont'd. Sealing Jaw Drive Vertical Overspeed Fault
- 0398 Sealing Jaw Drive Vertical CPU Watchdog Fault
- 0397 Sealing Jaw Drive Vertical Grnd Short Fault
- 0364 Sealing Jaw Drive Horizontal Physical Axis Fault
- 0396 Sealing Jaw Drive Vertical Physical Axis Fault
- 0392 Sealing Jaw Drive Vertical Bus Regulator Fault
- 0385 Sealing Jaw Drive Vertical Drive Thermal Overload
- 0384 Sealing Jaw Drive Vertical Motor Thermal Overload
- 0384 Cont'd. Sealing Jaw Drive Vertical Motor Thermal Overload
- 0382 Sealing Jaw Drive Horizontal Undertorque Limit Fault
- 0381 Sealing Jaw Drive Horizontal Overtorque Limit Fault
- 0380 Sealing Jaw Drive Horizontal Excessive Velocity Flt
- 0379 Sealing Jaw Drive Horizontal Position Error
- 0377 Sealing Jaw Drive Horizontal Undervoltage Fault
- 0377 Sealing Jaw Drive Horizontal Undervoltage Flt
- 0376 Sealing Jaw Drive Horizontal Overvoltage Fault
- 0378 Sealing Jaw Drive Horizontal Phase Loss
- 0373 Sealing Jaw Drive Horizontal Feedback Fault
- 0370 Sealing Jaw Drive Horizontal Motor Overtemp
- 0448 Gusseting Device Motor Thermal Overload
- 0451 Gusseting Device Converter Pre-charge Fault
- 0460 Gusseting Device Physical Axis Fault
- 0461 Gusseting Device Ground Short Fault
- 0462 Gusseting Device CPU Watchdog Fault
- 0120 Service Interval - Sealing Jaw Drive Vertical
- 0464 Gusseting Device Module Hardware Fault
- 0466 Gusseting Device Motor Overtemp
- 0467 Gusseting Device Duplicate Address Fault
- 0468 Gusseting Device Motion Instruction Error
- 0473 Gusseting Device Undervoltage Fault
- 0474 Gusseting Device Phase Loss
- 0475 Gusseting Device Position Error
- 0476 Gusseting Device Excessive Velocity Fault
- 0477 Gusseting Device Overtorque Limit Fault
- 0478 Gusseting Device Undertorque Limit Fault
- 0452 Gusseting Device Motor Feedback Fault
- 0456 Gusseting Device Bus Regulator Fault
- 0463 Gusseting Device Overspeed Fault
- 0469 Gusseting Device Feedback Fault
- 0471 Gusseting Device Overcurrent Fault
- 0472 Gusseting Device Overvoltage Fault
- 0513 No Axis Reference Jaw Drive Vertical
- 0544 HI Alarm Vertical Jaw Left
- 0512 No Axis Reference Jaw Drive Horizontal
- 0514 No Axis Reference Gusseting Device
- 0545 Sensor Fault Left Vertical Jaw
- 0549 HI Alarm Vertical Jaw Right
- 0550 Sensor Fault Vertical Jaw Right
- 0576 HI Alarm Front Jaw
- 0577 Sensor Fault Front Jaw
- 0578 No Change in Temperature on Front Jaw
- 0579 HI Alarm Rear Jaw
- 0580 Sensor Fault Rear Jaw
- 0582 HI Alarm Vertical Jaw
- 0583 Sensor Fault Vertical Jaw
External
Calculation Errors
- 0591 Calculation Error - Negative Path Limit X-axis
- 0592 Calculation Error - Positive Path Limit X-axis
- 0596 Calculation Error - Positive Path Limit Z-axis
- 0600 Calculation Error - Positive Path Limit Gusseting Device
- 0601 Calculation Error - Speed Limit Side Folding Unit
- 0593 Calculation Error - Speed Limit X-axis
- 0594 Calculation Error - Acceleration Limit X-axis
- 0595 Calculation Error - Negative Path Limit Z-axis
- 0597 Calculation Error - Speed Limit Z-axis
- 0598 Calculation Error - Acceleration Limit Z-axis
- 0599 Calculation Error - Negative Path Limit Gusseting Device
Vacuum
Volume Adjustment
Dosing
- 0479 Gusseting Device Other Fault, Call Service
- 0816 Volume Dosing Module/hardware Fault
- 0042 Wait for Dosing Unit
- 0817 Volume Dosing Drive Overtemp
- 0480 Auger Feeder Motor Thermal Overload
- 0483 Auger Feeder Converter Pre-Charge Fault
- 0815 Volume Dosing Overspeed Fault
- 0484 Auger Feeder Motor Feedback Fault
- 0814 Volume Dosing CPU Watchdog Fault
- 0813 Volume Dosing Ground Short Fault
- 0491 Auger Feeder External Input Fault
- 0481 Auger Feeder Drive Thermal Overload
- 0812 Volume Dosing Physical Axis Fault
- 0488 Auger Feeder Bus Regulator Fault
- 0492 Auger Feeder Physical Axis Fault
- 0808 Volume Dosing Bus Regulator Fault
- 0493 Auger Feeder Ground Short Fault
- 0494 Auger Feeder CPU Watchdog Fault
- 0806 Volume Dosing Module/config Fault
- 0495 Auger Feeder Overspeed Fault
- 0804 Volume Dosing Motor Fback Flt
- 0496 Auger Feeder Module Hardware Fault
- 0499 Auger Feeder Duplicate Address Fault
- 0801 Volume Dosing Drive Thermal Overload
- 0504 Auger Feeder Overvoltage Flt
- 0501 Auger Feeder Feedback Fault
- 0800 Volume Dosing Motor Thermal Overload
- 0510 Auger Feeder Undertorque Limit Fault
- 0818 Volume Dosing Motor Overtemp
- 0820 Volume Dosing Motion Instruction Error
- 0497 Auger Feeder Drive Overtemp
- 0498 Auger Feeder Motor Overtemp
- 0821 Volume Dosing Feedback Fault
- 0500 Auger Feeder Motion Instruction Error
- 0506 Auger Feeder Phase Loss
- 0823 Volume Dosing Overcurrent Flt
- 0824 Volume Dosing Overvoltage Fault
- 0508 Auger Feeder Excessive Velocity Fault
- 0511 Auger Feeder Other Fault, Call Service
- 0825 Volume Dosing Undervoltage Fault
- 0826 Volume Dosing Phase Loss
- 0505 Auger Feeder Undervoltage Fault
- 0827 Volume Dosing Position Error
- 0507 Auger Feeder Position Error
- 0509 Auger Feeder Overtorque Limit Fault
- 0828 Volume Dosing Excessive Velocity Fault
- 0708 Closure not Open Auger Feeder
- 0830 Volume Dosing Undertorque Limit Fault
- 0829 Volume Dosing Overtorque Limit Fault
- 0672 Auger not in Position
- 0704 Auger Feeder Calculation Error
- 0831 Volume Dosing Other Fault, Call Service
- 0705 Tendency Limit Reached
- 0774 Safety Switch Funnel Volume Dosage Unit
- 0736 No Reference Axis Volume Dosage
- 0768 Volume Dosage Calculation Error
- 0769 Safety Switch Volume Dosage Unit
- 0775 Volume Dosage Unit Stop Position
- 0803 Volume Dosing Converter Pre-charge Fault
- 0819 Volume Dosing Duplicate Address Fault
- 0417 Emptying Active
Misc
- 0032 Emergency Stop Control Panel
- 0426 Counter-blowing Vacuum Closure
- 0035 Emergency Stop Reserve
- 0503 Auger Feeder Overcurrent Fault
- 0607 Jam at Discharge Conveyor Outlet
- 0602 Calculation Error - Acceleration Limit Side Folding Unit
- 0654 No Valid Photo Cell Signal Detected
- 0706 Vacuum Monitoring Vacuum Closure
- 0718 Product Defect Infeed
- 0770 Product Jam in Funnel
- 0771 Remove Product Filling Tube
- 0772 Volume Dosage Unit Safety Cover
- 0773 Product Defect Infeed
- 0044 Machine is Waiting for Gas Flushing
- 0045 Product Detect Infeed
- 0096 Battery Control Logix
- 0098 Ram Memory Overload - restart Panel
- 0101 Barcode Scanner is Switched Off
- 0099 Printer Pre-alert
- 0100 Printer is Switched Off!
- 0227 Teach Phase Product Recognition Active
- 0371 Barcode Not Read
Film carriage
- 0034 Emergency Stop - Film Carriage
- 0444 Film Drive Excessive Velocity Fault
- 0445 Film Drive Overtorque Limit Fault
- 0441 Film Drive Undervoltage Fault
- 0442 Film Drive Phase Loss
- 0443 Film Drive Position Error
- 0446 Film Drive Undertorque Limit Fault
- 0447 Film Drive Other Fault, Call Service
- 0649 Rear Unwinder not in Position
- 0640 Film Carriage Limit Left
- 0641 Film Carriage Limit Right
- 0644 Fault on Frequency Converter Unwinder
- 0648 End of Film
- 0653 Cut and Splice Device Closed
- 0652 Splice Point Position
- 0655 Too Much Slippage on Film Drive
- 0660 Calculation Error - Speed Limit Film Drive
- 0661 Calculation Error - Acceleration Limit Film Drive
- 0355 Splice detection
- 0362 Film carriage limit left
- 0363 Film carriage Limit Right
- 0356 Splice point position
- 0357 Pre-alert Film End
Sealing
- 0365 Sealing Jaw Drive Horizontal Ground Short Fault
- 0366 Sealing Jaw Drive Horizontal CPU Watchdog Fault
- 0367 Sealing Jaw Drive Horizontal Overspeed Flt
- 0368 Sealing Jaw Drive Horizontal Module Hardware Fault
- 0383 Sealing Jaw Drive Horizontal Other Fault, Call Service
- 0650 Vertical Sealing Belt Faulty
- 0642 Fault on Frequency Converter Vertical Sealing Belt